Page 2 of 2

1
  thm_ft7478.jpg  
 
ft7478.jpg

Home  | Prev  | Next  | End

Email Advice to me from M0BCG

The ft747 seems susceptible so strong rf signals and static, the front end fuse/bulb can go often . i did mine twice and just replace with a meter lamp bulb , its fitted towards rear of tcvr not far from antenna input socket . the main mod is to link both sides of the filter board in 2 places where there are solder thru connections which become either dry or they just dont function properly . my ft747 has given up on me now , it wont switch on at all , played up and then got gradually worse until it stopped completely , i did try to fix it but its a little more than just the relay playing up , i havent bothered to look at it since and so i will probably just put it in cupboard . it was only a cheap battered one , worked for a few years and i cant complain , but not worth sending away for repair or anything . can get plenty of power out of them though , 125w on 10 and up to 200w on 80m . you say yours is down to half power . basically when you get the usual symptoms with them they will sometimes not come on receive and sometimes wont transmit , or the s meter will rise to s7 and stay there . the filter board is at rear of the main pcb, you can pull it out , is mounted on multi socket .

Forum notes from EHam

eHam Forums => Elmers => Topic started by: HP1KL on August 27, 2003, 03:02:26 PM


Post by: HP1KL on August 27, 2003, 03:02:26 PM
A few weeks ago I saw that a fellow ham had experienced exactly the same "symptoms" my FT-747-GX has: a sudden drop in reception, the S-meter swings high, and the output power drops. I have not found a solution, but my comments were wrongly attached to a string for another Yaesu model. I'm posting this in case someone else knows or can suggest what to check. Yaesu California did not have any suggestions, except to ship them the radio. Switching to AM sometimes helps "restore" performance. A fellow ham-tech replaced a relay and the radio was "real hot" for several weeks then once again "gave up the ghost!" Any suggestions appreciated '73 - HP1KL - Tony atconte@hotmail.com
Post by: M0BCG on August 27, 2003, 05:23:58 PM
i know the problem, i have details of the repair or FIX for this , it is just a problem with one small pcb that needs solder pads linking from both sides of pcb board. i have details in a Ham radio today magazine but will have to go to my workshop to get it from the shelf . will try to contact you when i have scanned the pages . this happened to me on an ft747 , easy fix once you know what to do hi hi . one thing first, please check the front end protection BULB , small wheatlamp bulb placed at rear left hand side of pcb , is mounted on a pin sticking up from pcb . if you have had a rf/static/lightning attack then you may have blown the bulb , it will need replacing . easy to check if the bulb is gone. can replace with a standard 12v meter lamp bulb .. 73 ian m0bcg
Post by: HP1KL on August 27, 2003, 11:28:32 PM
Ian: Thanks for your kind reply. I´ll be looking forward to your "fix" once you find your notes. Right now, a tech-ham friend has the radio [again] to check it out for me. I got high hopes [the first time I sent it to him] when he mentioned something similar to what you are saying -- the bad solder joint-jumper. It will be interesting to see if it is the same spot. I know about the bulb/attenuator/protector from the manual. I believe it is in series with the receiver and is recommended when one works below 10 MHz. But if this were the case, turning it off would by-pass it (I think) and the reception problem would be solved. It should not have any effect on the transmitter power, though. Anyway, once I get you note, I´ll pass on the tip and we will cross our fingers! Once again, many thanks! The 747 has an excellent receiver (most of the time), but when it won´t transmit, it is hopeless. Someone on the internet said 747´s were unreliable. Let´s hope we can prove him wrong. ´73s - Tony - HP1KL
Post by: M0BCG on August 30, 2003, 09:12:00 AM
tony , i sent you details of the magazine article , in an e mail to youre hotmail address, i hope it didnt bounce . i also posted mail to www.mods.dk and hopefully they will load up onto the website shortly . hope you get the ft747 working again .
Post by: HP1KL on September 01, 2003, 01:05:47 PM
Ian Many thanks -- I saw your note in my hotmail and got the info from wwww.mods.dk It took awhile to read because of the size. I think this is it! I´ll confirm once done. Many thanks again. ´73 -- Tony Conte - HP1KL
Post by: M1RKY on October 10, 2008, 07:56:10 AM
I know this threads old but wanted to say I had exactly the same problem with my FT-747. I did the mod to the filter board as described on mods.dk and it's been perfect ever since. Thank goodness google showed up this thread otherwise I'd have given up on on the radio. Such and eay fix too! Radio is as good as new.
Post by: AA5NI on April 15, 2009, 03:55:22 PM
I realize that this is an old problem. Anyone still have the info on the fiX? Any info would be appreciated.
Post by: HP1KL on April 15, 2009, 06:45:08 PM
Twice I tried replying direct from my Hotmail address, but delivery failed. This is the "fix" as published back in 2003 in MODS.DK See here: http://www.mods.dk/view.php?ArticleId=2824 This is the repair details for FT747, loss of receive and/or power. Signal meter rises or intermittent loss and return of power. I did this modification once to an ft747 that lost receive/transmit, it works. All credit to G3LLL Harry Leeming. This article has been read 7949 times.